Heating homes: 9 main systems

By: Hans De Keulenaer
Submitted: 2007-01-17 16:26:36
Print this article | Tell a friend | For publisher | Social Bookmarking
Rating:
 

Nine possible systems and a consideration
Until 250 years ago, wood and peat were the only means to heat a home. At present, there is a growing variety of residential heating systems. It is not easy to formulate an opinion which system is best in terms of environment, economy and comfort. But does the ideal heating system of the future really exist?

Each system has its own advantages and disadvantages. Which technology is the best should be evaluated on a case by case basis, without any prior exclusion of technologies.

Primarily nine different systems are being used today:

  1. Natural gas is the most environmentally friendly fossil fuel, especially when it is burned in a high efficiency boiler with heat recovery. Yet it requires a gas network. And maybe natural gas should be used for generating electricity?
  2. The oil boiler is a similar system to the gas boiler, yet with a higher emission rate. It doesn't require a network but a storage tank and road transport. The oil boiler is likely to loose market share in the upcoming years.
  3. Electrical heating has been out of grace for some time in some countries, but today it is again seen as one of the heating systems of the future. An electrical system can be an efficient and cost-effective alternative when electricity is generated from low carbon sources, or when the heating demand is relatively low - for instance in new, compact, and well isolated houses.
  4. The heat pump. Since it takes over 2/3 of its energy output from the environment, it has a very high efficiency. But a ground-water heat pump requires a large surface. It should be combined with a low temperature heating system in a well insulated house, but the investment is only cost-efficient if there is a sufficient heating demand. A best practice solution for relatively large buildings in temperate to cold climates. Reversible heat pumps could be used in climates where there is both a heating and cooling requirement.
  5. Domestic CHP (Combined Heat and Power) is an emerging technology. It has the advantage that it makes fully use of the capacity of natural gas to produce electricity - a high quality energy carrier. But it requires matching heat and electricity demand, and may produce too much heat for well insulated dwellings with relatively low heat requirements.
  6. District heating with a central CHP plant is only efficient in (compact) cities where buildings have a sufficient heat demand. So the better houses are insulated, the less interesting it becomes. Only in cold climates, the heating demand will still be large enough to justify an investment in district heating. An important consideration: if a district heating network already exists, reducing the heat demand of dwellings (e.g. by improved insulation) is still a good idea, since new technologies allow producing more electricity for a lower amount of heat.
  7. Coal stoves are regarded as an old-fashioned way for residential heating. Nevertheless, they are still commonly used in many countries. They produce a comfortable heat atmosphere and have a fairly good efficiency. But they are inconvenient to operate, and CO2 emissions are high. In Europe, the market share of coal as an energy source for heating will probably continue to decrease.
  8. Most coal stoves can also burn wood or wood pellets. The influence of wood pellets on the global CO2 emissions requires more investigation. Maybe wood should ideally be used for CO2 storage rather than energy carrier?
  9. Solar energy. A solar water boiler can be combined with low temperature heating. A wind or photo-voltaic system can be the energy source for electrical heating. None of both systems will be able to supply large power, so they should be used in houses with small heating demand or combined with other sources. Photo-voltaic systems have the disadvantage that they produce most power when the least heating is necessary, but solar cooling is an application where ambient generation will naturally match demand.
And to conclude a consideration. A house can be seen as our third skin, while our second skin consists of clothes. Reinforcing both skins can save a lot of energy, money, and CO2 emissions. The third skin can be improved by a maximum insulation, an excellent airtight construction, use of sun heat by intelligent glazing, and ventilation with heat exchange. The second skin can be improved by simply wearing an extra sweater! This allows setting the thermostat a bit lower - we know 1 degree results in a few % less energy per year.

Or we could use electricity even more intelligently. In Asia, so-called 'kotatsu' tables have an (electric) heating element underneath and a blanket and they are being used to heat just a small amount of space. They're quite comfortable, provide the emotional center for the home and one of the most efficient ways possible to provide high heating comfort to occupants. A similar system exists in Southern Spain.

In short, it is not easy to compare a variety of heating systems, used in different climates to provide various lifestyles.

------------------------------------------------------
Hans De Keulenaer manages Leonardo ENERGY initiative, the Web portal for sustainable energy professionals.

http://www.leonardo-energy.org

Article source: Expert Articles

Most Recent Articles in Science category

  • Hydrogen As a Fuel Source - By: Levi Quinn
    From water to air, there are a number of ways to energize your car. Alternatives to petroleum are a hot topic today. The growing concern for the environment is steadily increasing. It's an important issue that many people want to feel personally connected to. Hydrogen as a fuel source is not an entirely new idea. But science is taking a closer look at the impact that using hydrogen could have on both the environment and the economy. The best solutions are the ones that have more benefits than drawbacks.
  • MRI and Ultrasound: Two Vital Branches of Radiology - By: R Govindan
    Radiology was initially the branch of medical imaging that made use of x-rays on large flat sheets of photographic films for diagnosis. Modern day radiology is no longer confined to the practice of x-rays and now encompasses other methods of diagnostic imaging such as Computed Tomography (CT), Magnetic Resonance Imaging (MRI) and Ultrasound.
  • Processes Involved In Blavatsky's Writings and its effects - By: Edi Bilimoria
    Helena Petrovna Blavatsky (HPB) demonstrated the Siddhis (psychic-spiritual faculties) of clairvoyance, clairaudience, and the powers of projection, precipitation and being en rapport. These were all used in her writings on Occult science and Meta Physics which may be categorized into seven kinds of processes. We outline them below but it is emphasized that none of the above processes are miracles or supernatural
  • Biotech Development - By: Marcia Henin
    The development of Biotechnology and the affect it has in detecting Toxicity levels in the Human body.
  • Nanotechnology - Revolution in the Field of Medicine - By: Marcia Henin
    How science has learned to use Nanotechnology for bettering the process of Drug development.
  • Nanotechnology - Development in Water-Based Technology - By: Marcia Henin
    What is Nanotechnology and how does it applies in the science world - In this article, we will review some of the uses of Nanotechnology and its connection to the solubilization process.
  • The Z-Boson Mass and its Formula as Multiple Proofs in One Bowl of Yummy Pudding - By: Sean Sheeter
    A demonstration of the mathematical, theoretical and, especially, empirical connotations of the phrase "Pudding Proof" in the context of a highly exacting physical model. In particular, a formula is given deriving the mass of the Z-boson from two heavy quarks and and Higgs field. Remarkably, the precise correlation with the known value of the Z-mass is thus empirically proof positive of these far less directly measurable masses, which is further supported by arithmetic and theoretic construct.
  • The Theory, Significance and Precise Calculation of Gluino Mass - By: Sean Sheeter
    A preview of the most significant predictable particle cascades at Cern's LH-Collider in the coming years. Describes how a precise gluino mass of 6.388355 TeV relates to the super-symmetric Higgs mechanism and decays to squarks and other 'sparticles as a prerequisite to creation of 'dark mass,' as well as the unsolved puzzle of material baryon creation. Which also goes on to shows why giving three dimensionless calculations for the gluino mass are central to the e-course "241-Mumbers."
  • Derivation of the Pure Precise Fine-Structure Number and as a Ratio of Two Inexact Metric Constants - By: Sean Sheeter
    A history of a definitive answer to #1 'millennium question' of Strings 2000 in regard to whether all fundamental parameters can be determined in a dimensionless manner. Focus's on a 'pure' calculation of the fine-structure constant from a unified 'monolithic' system that allows precise equations for the full spectrum of fundamental particle masses from Higgs/SUSY to quarks, neutrinos and dark matter. With an update on controversies of determining the fine-structure from metric measures and a few other related issues.
  • Proof of the Exact Up and Down Quark Masses from the Pion Mass-Differential - By: Sean Sheeter
    A discussion of the equivalence of the mass differential between the charged and neutral pion as a function the mass difference between the down and up quark. Given the unprecedented mass value of the down quark = 7.763258 MeV, the up quark mass is calculable from the even more exacting d-u mass differential = 4.593453 MeV, where the experimental pion mass difference = 4.5936 plusmn.0005 MeV.